Chamberlain 942FPC Manual de usuario descargar pdf

Model 942FPC

Fingerprint Keyless Entry

Overview

The system uses biometric technology that enables an

authorized user to gain access by scanning their fingerprint.

The sensor strip on the unit makes a numeric template of the

fingerprint that is unique to that user

. The unit’s memory can

store up to four fingerprints.

• The term “enroll” refers to scanning the fingerprint so the

device will recognize the user

• The term “swipe” refers to the movement of the finger across

the sensor strip.

• The term “LED” stands for Light Emitting Diode. There are

6 LEDs located on the Fingerprint Keyless Entry

When unit is on, it is programmed to shut off after a short

period of time.

The unit’s sensor strip is sensitive so it is

important to read the Tips for Success before attempting to

use the Fingerprint Keyless Entry.

Carton Inventory

Receiver

Fingerprint Keyless

Entry

ENROLL

SEND

ENROLL

PAS S FAIL

READY RETRY

Step 1 Install the Receiver

1. Unplug the opener before proceeding.

2. OPEN RECEIVER: Insert a small screwdriver in slot on

receiver front panel as shown. Twist up actuator cover.

3. CONNECT RECEIVER AND OPENER: Remove about 1/4"

(6 mm) of insulation from each end of the 2-strand bell wire.

Connect one end to the receiver screw terminals (polarity is

NOT

required). Route wire along the channels and out the

bottom as shown.

4. Connect the other end of the bell wire to the two opener

terminals labeled “2” (white) and “1

” (red), “common” and

“command” or the terminals used for the push button control.

5. Use insulated staples to secure bell wire between receiver

and opener

. Length of bell wire depends on where the

receiver will be installed. Replace actuator cover.

6. Choose a 120Vac polarized outlet for the receiver which is

OUT

OF THE REACH OF CHILDREN. Plug receiver into

selected outlet. Return power to the opener.

Actuator Cover

Power Indicator Light

Terminals

Bell Wire

Channels

“SMART”

Indicator

Light

Connect Bell Wire

o Garage Door

Opener Terminals

“SMART”

Actuator

Bell

Wire

To prevent possible SERIOUS INJURY or DEATH from electrocution:

• Be sure power is not connected BEFORE installing the receiver.

To prevent possible SERIOUS INJURY or DEATH from a moving

gate or garage door:

• Install Keyless Entry Control within sight of the garage door, out of

reach of children at a minimum height of 5 feet (1.5 m), and away

from all moving parts of door

• ALWAYS keep remote controls out of reach of children. NEVER

permit children to operate, or play with remote controls.

• Activate gate or door ONLY when it can be seen clearly, is properly

adjusted, and there are no obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed.

NEVER permit anyone to cross path of moving gate or door

NOTICE TO U. S. CONSUMERS:

Some states prohibit the service or repair of garage door openers which

cannot be made to comply with the safety standards contained in UL

325 (1988 revision). In order to comply with both the letter and the spirit

of these laws, this universal radio control should not be used with

any LiftMaster

, Chamberlain

, or Sears Craftsman

garage door

opener manufactured prior to April 1, 1982. To find out if your

Chamberlain-made garage door opener was manufactured prior to or

after April 1, 1982, please call 1-800-528-9131 before installing this

universal radio control.

Step 2 Install the Keyless Entry

1. Remove cover.

2. Fasten bottom screw to mounting surface. Allow 1/8"

(3 mm) to protrude above surface. Position unit on screw

head and adjust for snug fit.

3. Fasten top screw. Replace cover.

1 2 3 4 5 6 7 8

Indice de contenidos

Pagina 1 - Fingerprint Keyless Entry

®Model 942FPC Fingerprint Keyless Entry Overview The system uses biometric technology that enables an authorized user to gain access by scanning the

Pagina 2 - Step 3 Enroll Initial User

Tips for Success CORRECT 1. Make sure finger is clean and dry. Place finger flat above the sensor strip with the top knuckle above the sensor. 2. Swip

Pagina 3 - Step 6 Operation

Step 5 Programming NOTE: The unit must have an enrolled user before it can be programmed to the receiver. Due to the 30 second time interval, a second

Pagina 4 - Troubleshooting

Erase/Reset • To erase users: NOTE: Erasing a user will erase ALL stored fingerprints. User does NOT need to reprogram to opener. 1. Open cover and wa

Pagina 5 - VERTISSEMENTAAVERTISSEMENT

ATTENTIONAVERTISSEMENT AVERTISSEMENTAVERTISSEMENT®Modèle 942FPC Ouverture sans clé à empreintes digitales Caractéristiques Le système utilise une tech

Pagina 6 - CORRECT

Conseils utiles CORRECT 1. Vérifiez que votre doigt est propre et sec. Placez votre doigt au-dessus du capteur de bande, votre l’articulation du haut

Pagina 7 - Étape 6 Fonctionnement

Étape 5 Programmation REMARQUE : L’appareil doit avoir un utilisateur inscrit avant d’être programmé au dispositif de récepteur. Éttant donné l’interv

Pagina 8

ATTENTIONAVERTISSEMENT AVERTISSEMENTAVERTISSEMENTSuppression/Réinitialisation • Pour supprimer des utilisateurs : REMARQUE : La suppression d’un utili

Comentarios a estos manuales

Sin comentarios

Chamberlain 942FPC Manual de usuario

Busca en linea o descarga Manual de usuario para No Chamberlain 942FPC. Chamberlain 942FPC User's Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para No Chamberlain 942FPC